SWITCHING AMPLIFIER 521

ELECTRONIC ACCESSORY | DISPLAY AND CONTROL DEVICES

Application

The switching amplifier is preferably used for binary signal transmission of water meters.
The switching amplifier is frequently used as pulse extension relay for fast running processes. It can be used as contact protection relay or non-bounce relay when being triggered by a volt-free contact transmitter (reed switch).
If required, the two binary inputs can be added to one output-channel (via turn switch).

Features

  • Snap-bar case version
  • Triggered on choice by contact transmitter, infrared transmitter and two-wire primer (NAMUR)
  • Each output is a opto-coupler with one no-contact
  • Two volt-free outputs, solid state relay, no-contact
  • Galvanically isolated measurement and supply circuits
  • Adjustable impulse period
  • 3 different pulse length, adjustable via turn switch
  • Pulse-addition adjustable via turn switch
  • Power supply 20 ... 250 V AC/DC
  • Technical Data
    Supply voltageWide range power supply 20 ... 250 V AC/DC, 100 mA ... 20 mA
    DisplayLED display for output pulses
    Storage temperature°C-40 ... +70
    Operating temperature°C0 ... +55
    Output - typeSolid stay relay (SSR), output volt-free
    Output - loadMax. 230 V / 100 mA ~
    Min. input pulse duration6 ms
    Max. input pulse durationInfinite
    OutputsCan be switched over via turn switch; S1 = Channel 1, S2 = Channel 2
    InputsInitiator 571 / 572; Reed switch 570, IR transmitter 571, PV14
    Housing - typeSnap-on housing
    Housing - fixingMounting rail to EN 50022 (35 x 7.5)
    Protection class - housingIP20
    Protection class - terminalIP10
    Weightg200
    Separate working outputs (SX = Channel 1 or Channel 2)
    SX = 0 | OutputX = InputX --> direct transmission / permanent contact
    SX = 2 | OutputX = InputX with 0.1 sec output pulse __|¯|_________
    SX = 3 | OutputX = InputX with 0.3 sec output pulse __|¯¯¯|_______
    SX = 4 | OutputX = InputX with 2 sec output pulse __|¯¯¯¯¯¯¯|___

    Input-Addition (Channel 1 + 2) --> OutputX (max. up to 100 pulses per channel in memory)
    SX = 9 | OutputX = E1 + E2 with 0.1 sec output pulse __|¯|_________
    SX = A | OutputX = E1 + E2 with 0.3 sec output pulse __|¯¯¯|_______
    SX = B | OutputX = E1 + E2 with 2 sec output pulse __|¯¯¯¯¯¯¯|___
  • Technical Data Inputs
    Initiator 572, 5738 mA (short-circuit-current), 1.6 mA (switching point)
    Reed switch 5708 mA (short-circuit-current), 1.6 mA (switching point)
    IR transmitter 5715 mA (short-circuit-current), 1.0 mA adjustable by front trimmer (switching point)
    PV145 mA (short-circuit-current), 1.0 mA (switching point)
  • Dimensions
    LengthLmm72
    WidthBmm91
    WidthB1mm65
    WidthB2mm46
    HeightHmm62
    HeightH1mm51
    HeightH2mm33
  • Order References
    RemarkSwitching Amplifier (Snap Bar) (SSR) 20 ... 250 V AC/DC
    Article number521 000 16
  • Operation turn switch | Connections

  • Pin Assignment
  • Connection of sensors

  • Connection of sensors / meters